Japan's Teijin PC models: Teijin Polycarbonate PC TEIJIH Panlite series models: Teijin TEIJIH Panlite Series Polycarbonate PC: LN-3000RM Teijin TEIJIH Panlite Series Polycarbonate PC: LN-1010RM Teijin TEIJIH Panlite series Poly carbonate fat PC: EN-8615N Teijin Polycarbonate TEIJIH Panlite series PC: EN-8515N Teijin Polycarbonate TEIJIH Panlite series PC: E-8715日本帝人 TEIJIH Panlite Series Polycarbonate PC: LV-2225L Teijin TEIJIH Panlite Series Polycarbonate PC: LN-3010RM TEIJIH Panlite series Teijin Polycarbonate PC: LN-2520A Series TEIJIH Panlite Teijin Polycarbonate PC: LN-2250Y Teijin TEIJIH Panlite Series Polycarbonate PC: LN-1250G Teijin TEIJIH Panlite Series Polycarbonate PC: LV-2250Y Teijin TEIJIH Panlite Series Polycarbonate PC: L-1250ZW TEIJIH Panlite series Teijin Polycarbonate PC: LV-2225Y Teijin TEIJIH Panlite Series Polycarbonate PC: LV-2225L Teijin TEIJIH Panlite Series Polycarbonate PC: L-1250Y Teijin TEIJIH Panlite Series Polycarbonate PC: L-1250日本帝人 TEIJIH Panlite Series Polycarbonate PC: L-1225日本帝人 TEIJIH Panlite Series Polycarbonate PC: K -1300Y Process characteristics: water absorption larger PC plastic materials, must be preheated and dried before processing, drying of pure PC 120 ℃, modified PC for general use temperature 110 ℃ dried over four hours. Drying time can not exceed 10 hours. Generally available air extrusion determine whether sufficient drying. Use ratio up to 20% recycled material. In some cases, the use of 100% recycled materials, the actual amount depending on the product quality requirements. Recycled materials can not mix different masterbatch, otherwise it will seriously damage the properties of the finished product. Mold and gate design common mold temperature of 80-100 ℃, plus glass of 100-130 ℃, small articles needle-shaped gate, gate depth should be 70% of the thickest part, the other a ring and a rectangular gate . The bigger the better runner Bayer PC plastic materials distributor in China, in order to reduce the plastic is caused by excessive shear defects. Vent depth should be less than 0.03-0.06mm PC plastic materials, flow channel as short and round, stripping slope is generally about 30'-1. Melt temperature of the air injection can be used to determine the level of the processing temperature. General PC plastics processing temperature 270-320 ℃ PC plastic materials do not become brittle cold and super toughness, some modified or low molecular weight PC plastic materials is 230-270 ℃. Injection speed too fast injection speed is more common with molding, electrical switches such as playing pieces. Common to Slow - rapid prototyping. Back pressure back pressure 10bar about PC polycarbonate plastic raw materials priced at wholesale, in the absence of gas lines and mixing conditions can be appropriately reduced. The residence time in the long residence time at high temperature, the material will be degraded, put also CO2, turns yellow. Do not use LDPE, POM, ABS or PA cleaner cartridge. Application of PS cleanup. Supply UV PC plastic materials _ Jichang plastic _PC plastic materials provided by the Dongguan City, often Jichang plastic materials. Dongguan Chang-ping Jichang plastic materials (jichang668.1688.com/)(www.POM100.COM) is Dongguan, a leader in engineering plastics for many years, the company implement the scientific management, innovation and development, the principle of honesty and trustworthiness, and satisfy customer needs. In Jichang plastic leadership with the staff warmly welcome all inquiries negotiations to create a better future Jichang plastic.